The SensorSwitch included in the set acts as the external actuator for the electronic switches inside the PowerBox Cockpit.

The SensorSwitch 
The SensorSwitch included in the set acts as the external actuator for the electronic switches inside the PowerBox Cockpit.  Features:

• For Spektrum and Jeti satellites, Futaba S-BUSand Multiplex M-LINK receivers
• All channels from the receiver are transferred using a three-core lead
• Complete receiver redundancy, double the security
• Complete battery redundancy: two batteries, two electronic switches, redundant output voltage with dual regulation
• Spektrum with four satellites, Futaba with two S-Busreceivers, Multiplex with two M-Link receivers, Jeti with two satellites
• High-resolution graphic OLED screen with 128 x 64 pixels
• Ultra-simple menu-based programming using the SensorSwitch
• Eleven channels + one channel for door sequencer
• Downlink channel transmission for Spektrum and MPX
• Unrestricted channel assignment for all output sockets, (channel output mapping)
• Synchronised servo outputs for totallysimultaneous servo movements
• Four-stage user-variable servo frame rate (12 ms, 15 ms, 18 ms, 21 ms)
• Integral freely programmable door sequencer
• The unit saves receiver data, such as "lost frames" and "failsafes", for all connected receivers - whether Spektrum, Futaba, Multiplex, Jeti. Data can be read out after the flight on the OLED screen
• Four match-channels for two servos each; both servos individually variable
• 16-bit processor for high-speed, high-resolution signal processing
• Signal amplification for a total of 12 channels and 21 servos
• Direct transmission of battery voltages and capacities to the transmitter (downlink channels)
• On-screen voltage display for each battery separately, with bar indicator
• Residual capacity display for both batteries separately
• User-variable servo voltage: choice of 5.9 V or 7.4 V
• Minimum value memory shows any voltage collapses
• Large-area heat-sink for high regulator capacity
• Regulator monitor and regulator error indicator
• Supports three battery types: LiPo, LiIon, NiMH / NiCd, LiFePo
• Suppression of any servo feedback currents which might occur

• Bus systems for seriell receivers from: Spektrum, Futaba, Multiplex, Jeti
• Operating voltage: 4,0 Volts to 9,0 Volts
• Power source: 
  2 x two-cell LiPO batteries 7,4 Volts
  2 x five-cell NiCd or. NiMH batteries
  2 x two-cell LiFePo batteries 6,6 Volts (A123)
• Current drain:
  Power-on state approx. 130 mA 
  Power-off state approx. 15 µA
• Dropout voltage: approx. 0,25 V
• Max. seriell receiver current
  2 x 3 A (stabilised)
• Max. servo current: 
  according to efficiency of cooling
  Peak 2 x 20 A
• Servo signal resolution: 0,5µs
• Signal frame rate:
  User variable: 12ms, 15ms, 18ms, 21ms
• Screen: OLED 128 x 64 pixels, graphic
• Servo sockets: 21 sockets, 12 channels, 4 of them match-channels,
  single-channel door sequencer with 6 servo sockets
• Temperature range: - 30 °C to + 75 °C
• Dimensions: 110 x 72 x 24 mm 
  (incl. base plate)
• Weight: 115 g
• SensorSwitch: 15 g
• EMV approval: EN 55014-1:2006
• CE approval: 2004/108/EG

 Operating Instructions (PDF 8.8 MB)
 
 Certification(PDF 68 KB)
 
 Test Report(PDF 528 KB)